6640A REV K Norge Washer Parts List

Drive belt (belt drive)

This dryer drum drive belt is 89.5" long and has four ribs. This part helps spin the drum during the drying cycle.

Lower spray arm

Lower front dishrack wheel (front roller & stud)

This wheel is located on the front lower rack. It includes the axle. Sold individually.

Dryer drum support roller (use wpl 8536974)

The drum support roller has a metallic bearing in its center. This part is used to hold the drum in place in the cabinet while letting the drum rotate on the support rollers. If your dryer is noisy, will not tumble or takes too long to dry, you might need to replace the roller. It is recommended that you replace both rollers at once. This is a genuine OEM part and is sold individually. Please remember to shut off the power to the dryer before starting the repair.

Dishwasher upper rack adjuster (adjuster)

Upper rack adjuster kit - white wheels, left and right sides (adjuster, arm assembly)

Light bulb - 40w 130v (lamp 1/2 size)

This 40 watt, 130-volt clear appliance light bulb is for your microwave. The light bulb is used on the inside of your microwave to provide light when the door is open or below the microwave to provide light for the cooking area. It is clear in color and has a small screw-in base. If your current bulb is burnt out or broken you will need to replace it. This bulb is a genuine OEM part and is sold individually.

Terminal block kit (use 5301167733)

This surface burner terminal block kit comes with interchangeable mounting brackets, ceramic wire nuts, heat shrink protective tubing and wires. This part is used to connect the wire harness to the surface burner element. If your element will not heat at all, or is not heating properly, it is likely an issue with the terminal block and will need to be replaced. This is a genuine OEM part. Please remember to disconnect the power supply before starting your repair.

Worm following gear (worm gear)

The follower gear works in conjunction with the worm gear and is part of the gear system that powers the mixer. If the mixer is making noises and not mixing you may need to replace this gear. This is a genuine OEM manufacturer-approved gear, used in stand mixers. Please remember to disconnect the power to the mixer before starting the repair.

Refrigerator crisper drawer (pan-crispr)

The crisper drawer with humidity control allows you to adjust the humidity within the crisper. By adjusting the humidity, it will extend the life of your produce. The crisper drawer is made of clear plastic, measures 13 1/2” wide and 18 1/2” deep. The drawer does not include the white trim on the front. This is a genuine OEM part and is sold individually.

Refrigerator center crisper drawer slide rail - white (support, center crisper drawer)

This is the center support rail for the crisper drawers. The rail attaches to the shelf frame between the two crisper drawers to provide support for the drawers as they slide in and out. The support rail is white in color and made of plastic. It measures approximately 13.5-inches in length and is a genuine OEM part.

Multi rib belt (sub 40111201)

This dryer drum belt has five ridges, 93-3/8 inches in length, and 3/8 of an inch wide. It is flat, black in color, and is made entirely of rubber. The belt helps rotate the drum. If the drum does not rotate and you can still hear the motor running, the belt may have broken and will need to be replaced. This is a genuine OEM part. Please remember to disconnect the power to your dryer before starting the repair.

Water inlet valve (valve-inlt)

This genuine replacement water inlet valve with tubing supplies water to the ice maker and water dispenser. The valve is 120 volts and 50/60 Hz. If your ice maker is not making ice or no water is coming from the dispenser, you may need to replace this part. The manufacturer has updated the water inlet valve and it no longer includes the removable pre-filter bracket. If you are unable to reuse the old removable pre-filter bracket, order part number WPW10445062. Please remember to disconnect the water and power supply before starting your repair.

Upper spray arm mount (upper spray arm mounting bracket)

**Please note: This mount has been redesigned by the manufacturer for efficiency. The top mounting clip and screw are no longer needed.

Dryer high limit thermostat (thrmst-fix)

The three-terminal high-limit thermostat with a terminal extension arm acts as a safety mechanism that keeps the dryer from overheating. When the dryer temperature reaches 221 degrees Fahrenheit, the thermostat will shut off power to the heating element until it drops by 80 degrees Fahrenheit. If your dryer has no heat, takes too long to dry or the thermostat has shorted out, you will need to replace the thermostat. This is a genuine OEM part. Please remember to disconnect the power to your dryer before starting the repair.